The worst thing that you can find in your newly built home is mold, but it is something that is built into homes these days by careless contractors bent on getting the job done with as little effort as possible on their part. As the employer of the contractor, it is your responsibility and in your best interests to be at the job site on a regular basis to ensure that the building materials that your contractor purchased to build your home with are both up to your standards and that they are handled correctly.
Your contractor should have purchased only the materials that you outlined in your contract with him or her to purchase. They should have purchased nothing more and nothing less. None of these materials, especially drywall, should be stored directly upon the ground where it comes into contact with the soil. They should be stored on tarps or raised up off the ground in some way. This will help ensure that mold does not start to grow on them before they are used in the construction of the house.
The building site should also be covered with tarps before it rains until the roof and walls are put up to protect the interior of the structure.
Before you hired your contractor, you should have obtained references from him or her to determine the quality of their craftsmanship. This is something that you should do when hiring anyone to do almost anything for you concerning an investment such as this. You should ask the references whether they have had any problems with mold or water damage since their home was built and if it was due to bad construction or not. As long as your contractor is known for good building practices, you should have no problem with the way that he treats the building materials for your house.
It is unfortunate that you cannot be at the site of your home’s new construction all the time, but the more you are able to check on the progress of your home’s construction, the better. You should have a mold inspector come and inspect the property at least twice, once during the middle of the construction and again once it is completed to determine that there is no mold growing in the home.
Jim Corkern is a writer and promoter of quality
Connecticut Mold Remediation services and other states such as
north carolina mold remediation companies across the united states.
Saturday, September 29, 2007
Home Building Contractors
Having a home built for you is a tricky procedure, especially since there are so many different factors to consider. The first thing that you need to think of, though, is just who you will hire to do this task for you. There are a large number of contractors out there that would love to do the job, but the fact is that not all of them are honest or completely up to the task of making sure it gets done correctly. Many contractors have been known to use poor quality materials, even if they are up to local building code standards. They may end up causing damage to your home, but you cannot do anything about it as long as the materials the contractor used are up to local structural codes.
When choosing a contractor, you should talk to people that you know and trust first to find out if they can recommend anyone for the job. Only after you have exhausted these resources should you look to the local phone book. No matter which method you use, you should obtain at least three different references from at least three different contractors so you will have some options. Contact each of the references and ask if the newly built home has had any problems with mold or water damage since the construction was finished. Other structural problems should also be asked about.
After you have gotten a few different contractors to choose from that you find to be reputable, ask each one of them for a fixed price bid based on the building plan that you give to them and what materials you want the home built out of. They may try to get you to accept a time and materials contract, but this can be tricky, since time and materials contract allow the price to vary depending on different factors such as the cost of labor and building materials. They may quote you a low price in the beginning, but it can quickly rise as unexpected issues come up with the building process.
The contract with your contractor should be very specific as to what is covered in it. It should include the date that the project will begin and a date by which it should be finished and also include what specific building materials you wish for the home to be built out of so that your contractor does not have much room to substitute other, lesser materials.
Jim Corkern is a writer and promoter of quality
Connecticut Mold Remediation services and other states such as
north carolina mold remediation companies across the united states.
When choosing a contractor, you should talk to people that you know and trust first to find out if they can recommend anyone for the job. Only after you have exhausted these resources should you look to the local phone book. No matter which method you use, you should obtain at least three different references from at least three different contractors so you will have some options. Contact each of the references and ask if the newly built home has had any problems with mold or water damage since the construction was finished. Other structural problems should also be asked about.
After you have gotten a few different contractors to choose from that you find to be reputable, ask each one of them for a fixed price bid based on the building plan that you give to them and what materials you want the home built out of. They may try to get you to accept a time and materials contract, but this can be tricky, since time and materials contract allow the price to vary depending on different factors such as the cost of labor and building materials. They may quote you a low price in the beginning, but it can quickly rise as unexpected issues come up with the building process.
The contract with your contractor should be very specific as to what is covered in it. It should include the date that the project will begin and a date by which it should be finished and also include what specific building materials you wish for the home to be built out of so that your contractor does not have much room to substitute other, lesser materials.
Jim Corkern is a writer and promoter of quality
Connecticut Mold Remediation services and other states such as
north carolina mold remediation companies across the united states.
Getting the Right Contractor
There are a number of factors that you need to consider when hiring a contractor to build your new home and the process of finding the right one can be somewhat tricky. While you may think that hiring a contractor is a few simple steps, but a lot of it can be attributed to your own intuition.
Talk to your relatives and friends and find out if they can recommend a good contractor to you. This is the most reliable way to do find a contractor to build your house, but if you do not have anyone that you can talk to or they cannot recommend anyone, then you should try the phone book. The general consensus is to never use the phone book to hire people to work on your home, but not all of us have the friends or relatives that can give us advice on who to choose.
Get in touch with a few different contractors and ask for at least three references from each one and contact them all. Ask if they have had any issues with water damage or mold in their newly constructed home and ask about other structural problems that might exist. Write down what you discover about each contractor and use this to make a decision on who to offer the job. Get a fixed price bid from the ones you think are good enough for the job and make sure they get the same building plan.
Your contract with them should have a number of specifics in it so that there is no room for confusion as to what is expected of your contractor. Dates showing where the project should begin and approximately when it should end are to be included along with a list of materials the home will be built out of. Consider offering incentives to your contractor if the job is completed early and offer penalties if the job is not completed by a certain date if moving in as soon as possible is important to you.
Any contractor that you hire should have the proper insurance for himself and his workers so workers are covered by his insurance while they are working on your property. You need to obtain copies of all these insurance policies and keep them in a job folder along with other necessary documents like your building contract and a payment schedule.
You should make payments to your contractor as work progresses and do not let your payments get ahead of the work that has been done.
Jim Corkern is a writer and respected contributor to the Water damage restoration and mold remediation Industry. Visit his sites for more information.
http://www.moldrestorationny.info
http://www.moldrestorationnj.info
Talk to your relatives and friends and find out if they can recommend a good contractor to you. This is the most reliable way to do find a contractor to build your house, but if you do not have anyone that you can talk to or they cannot recommend anyone, then you should try the phone book. The general consensus is to never use the phone book to hire people to work on your home, but not all of us have the friends or relatives that can give us advice on who to choose.
Get in touch with a few different contractors and ask for at least three references from each one and contact them all. Ask if they have had any issues with water damage or mold in their newly constructed home and ask about other structural problems that might exist. Write down what you discover about each contractor and use this to make a decision on who to offer the job. Get a fixed price bid from the ones you think are good enough for the job and make sure they get the same building plan.
Your contract with them should have a number of specifics in it so that there is no room for confusion as to what is expected of your contractor. Dates showing where the project should begin and approximately when it should end are to be included along with a list of materials the home will be built out of. Consider offering incentives to your contractor if the job is completed early and offer penalties if the job is not completed by a certain date if moving in as soon as possible is important to you.
Any contractor that you hire should have the proper insurance for himself and his workers so workers are covered by his insurance while they are working on your property. You need to obtain copies of all these insurance policies and keep them in a job folder along with other necessary documents like your building contract and a payment schedule.
You should make payments to your contractor as work progresses and do not let your payments get ahead of the work that has been done.
Jim Corkern is a writer and respected contributor to the Water damage restoration and mold remediation Industry. Visit his sites for more information.
http://www.moldrestorationny.info
http://www.moldrestorationnj.info
Fires And The Smoke Point of Oil
If you cook a lot at home and with oil, then you are probably at least somewhat aware of what a smoke point refers to. Even some of us who do cook fried or stir fried foods often are not fully aware of what a smoke point is and what it might be for the particular kind of oil that we are cooking with. It is something that every cook should be familiar with, since not knowing the smoke point of the oil that you are cooking with can cause it to catch on fire. Some of the worst house fires ever have been started by cooking with oil in the kitchen and by knowing the smoke point of what you are cooking with, you can reduce the chances of having an oil fire greatly.
Unrefined oils that have been harvested using what is called cold extraction tend to have a lower smoke point than other kinds of oil. These unrefined oils usually have better flavor than refined oils and are usually used in sautéing, baking, and for salad dressings. Unrefined oils tend to include avocado oil, some nut oils, and olive oils. Oils that have high smoke points are generally peanut oil, canola, soy, and safflower oil.
A pan containing oil that has reached its smoke point needs to be removed immediately and let to cool. After it cools, it should be thrown out for a number of reasons. Oil that reaches its smoke point starts to break down and will taste very bad, which is why any kind of oil that has reached its smoke point should be thrown out. It will make the food taste bad and the smoke should not be breathed in or the oil consumed, since it can form carcinogens.
You should heat oils gradually because they will perform better than if you just pour them into a very hot pan. As long as they are heated up and cooled off slowly, you can reuse most oils, but you should throw them away as soon as they start to discolor or smell rancid.
One of the worst things that you can do is leave oil to heat in the kitchen on its own. A home catching on fire and burning down completely is not an uncommon occurrence when there is unattended oil heating in the kitchen. What makes this another very bad situation is that oil and electrical fires cannot be put out with water, no matter how much of it you throw on it. If your oil or stove catches on fire and it is fairly small, you can put it out effectively by using baking soda or using your fire extinguisher. Anyone who cooks with oil on a regular basis should have both of these items close by, just in case.
Jim Corkern is a writer and promoter of quality
New Jersey Sewage Damage Cleanup and other states such as
New York mold remediation companies across the united states.
Unrefined oils that have been harvested using what is called cold extraction tend to have a lower smoke point than other kinds of oil. These unrefined oils usually have better flavor than refined oils and are usually used in sautéing, baking, and for salad dressings. Unrefined oils tend to include avocado oil, some nut oils, and olive oils. Oils that have high smoke points are generally peanut oil, canola, soy, and safflower oil.
A pan containing oil that has reached its smoke point needs to be removed immediately and let to cool. After it cools, it should be thrown out for a number of reasons. Oil that reaches its smoke point starts to break down and will taste very bad, which is why any kind of oil that has reached its smoke point should be thrown out. It will make the food taste bad and the smoke should not be breathed in or the oil consumed, since it can form carcinogens.
You should heat oils gradually because they will perform better than if you just pour them into a very hot pan. As long as they are heated up and cooled off slowly, you can reuse most oils, but you should throw them away as soon as they start to discolor or smell rancid.
One of the worst things that you can do is leave oil to heat in the kitchen on its own. A home catching on fire and burning down completely is not an uncommon occurrence when there is unattended oil heating in the kitchen. What makes this another very bad situation is that oil and electrical fires cannot be put out with water, no matter how much of it you throw on it. If your oil or stove catches on fire and it is fairly small, you can put it out effectively by using baking soda or using your fire extinguisher. Anyone who cooks with oil on a regular basis should have both of these items close by, just in case.
Jim Corkern is a writer and promoter of quality
New Jersey Sewage Damage Cleanup and other states such as
New York mold remediation companies across the united states.
Friday, September 7, 2007
Water Damage and Interior Paint
Using waterproof paint to help prevent water damage to the walls and ceilings of your home is an option for most of us. The everyday wear and tear on the interior of our homes comes from all the areas in the home that are moist by nature such as the bathroom, the laundry room, kitchen, and basement. Showering, washing dishes, hot baths, and the steam from cooking all cause the water damage and discoloration of our walls and ceilings, but with waterproof paint, this does not have to be so.
Not only does water discolor the ceiling and cause the paint on your walls to peel, but it can also cause mold to grow in these areas, which introduces a new health risk to the indoor environment. Moisture becomes trapped under a layer of paint that allows it to seep in and mold begins to grow underneath it.
The best places for you to apply waterproof paint if you cannot apply it to the entire home are the areas that are most subject to the exposure of water vapor and steam. These are typically the kitchen, bathroom, laundry room, and your basement. Your bathroom and kitchen are the ones that you should concentrate on first, since every member of your household will have to go into these rooms at least once or twice every single day.
Using a primer that is waterproof and mold resistant is also good to use in these areas. The primer that you use does not have to be mold resistant, but it is definitely a plus. Finding one that is stain resistant is also good, since you will not have to repaint very often.
When it comes to just what kind of paint you need to apply to different things in your home, it depends on what kind of surface you intent on applying it to. A high-gloss paint is typically easy to clean, but if there are any flaws in the surface that you paint with it, they will all show up in perfect detail. Semi-gloss paints have less shine than high-gloss paints do, but these are easier to clean than high-gloss. Eggshell and flat finishes are the easiest to cleanse and these paints are starting to become more widely used since higher quality paints are becoming available in these no-gloss finishes.
Water damage, mold, and stains are all common household problems, but applying waterproof, stain resistant, and mold resistant paints to the moist areas of your home should help prevent a good bit of it.
Chicago Water and Sewage Extraction
North Carolina Water and Sewage Extraction
Not only does water discolor the ceiling and cause the paint on your walls to peel, but it can also cause mold to grow in these areas, which introduces a new health risk to the indoor environment. Moisture becomes trapped under a layer of paint that allows it to seep in and mold begins to grow underneath it.
The best places for you to apply waterproof paint if you cannot apply it to the entire home are the areas that are most subject to the exposure of water vapor and steam. These are typically the kitchen, bathroom, laundry room, and your basement. Your bathroom and kitchen are the ones that you should concentrate on first, since every member of your household will have to go into these rooms at least once or twice every single day.
Using a primer that is waterproof and mold resistant is also good to use in these areas. The primer that you use does not have to be mold resistant, but it is definitely a plus. Finding one that is stain resistant is also good, since you will not have to repaint very often.
When it comes to just what kind of paint you need to apply to different things in your home, it depends on what kind of surface you intent on applying it to. A high-gloss paint is typically easy to clean, but if there are any flaws in the surface that you paint with it, they will all show up in perfect detail. Semi-gloss paints have less shine than high-gloss paints do, but these are easier to clean than high-gloss. Eggshell and flat finishes are the easiest to cleanse and these paints are starting to become more widely used since higher quality paints are becoming available in these no-gloss finishes.
Water damage, mold, and stains are all common household problems, but applying waterproof, stain resistant, and mold resistant paints to the moist areas of your home should help prevent a good bit of it.
Chicago Water and Sewage Extraction
North Carolina Water and Sewage Extraction
Areas in the Bathroom Prone to Water Damage
Since your bathroom is one of the most important rooms in the house, you need to be aware of the different areas of it that are the most at risk for water damage. These are the water junctions in your bathroom and this means that these are the areas that water comes out of the plumbing and into the room at some point, whether it is at the shower, the sink, or the toilet.
Having tile down in your bathroom to protect the floor underneath from water is an absolute must. While you can put down carpet in the bathroom, this is not advised, since mold will eventually start to grow in it or under it, especially in the bathroom closet where you are likely to throw wet towels and clothes. These wet items are usually forgotten about and dry clothing is thrown on top of them.
Do an inspection of your bathroom when you go in it every now and then to make sure that there are no real signs of water damage occurring.
The tiles on the floor and on the walls around the shower and bath tub can become cracked over time and when they do become cracked, you need to replace them to keep water from seeping under them. Water that gets under these tiles will damage the surface underneath and if they become very damaged, tearing up the tile and replacing this surface is the only option to maintain structural integrity.
The plumbing under the sink should be inspected for leaks on a regular basis and you should replace the pipes if they are cracked or loose at all.
You should also pay attention to the area around the base of the toilet and cracked tile around it needs to be replaced. Toilets overflow all the time from clogging and you can prevent this most of the time by just not putting too much toilet paper in the toilet. Also avoid putting hanging toilet bowl cleansers in it, because these also tend to cause clogging.
The plumbing inside the walls can be checked out, but this is the most difficult area of the bathroom to keep an eye on, since the pipes are located inside the walls. Watch for moisture on the drywall or leaking into the floor from any part of the wall. Either of these signs should be a giveaway that there is a problem in the wall.
Texas Residential Water Damage Restoration Contractors
Water Damage Restoration
Having tile down in your bathroom to protect the floor underneath from water is an absolute must. While you can put down carpet in the bathroom, this is not advised, since mold will eventually start to grow in it or under it, especially in the bathroom closet where you are likely to throw wet towels and clothes. These wet items are usually forgotten about and dry clothing is thrown on top of them.
Do an inspection of your bathroom when you go in it every now and then to make sure that there are no real signs of water damage occurring.
The tiles on the floor and on the walls around the shower and bath tub can become cracked over time and when they do become cracked, you need to replace them to keep water from seeping under them. Water that gets under these tiles will damage the surface underneath and if they become very damaged, tearing up the tile and replacing this surface is the only option to maintain structural integrity.
The plumbing under the sink should be inspected for leaks on a regular basis and you should replace the pipes if they are cracked or loose at all.
You should also pay attention to the area around the base of the toilet and cracked tile around it needs to be replaced. Toilets overflow all the time from clogging and you can prevent this most of the time by just not putting too much toilet paper in the toilet. Also avoid putting hanging toilet bowl cleansers in it, because these also tend to cause clogging.
The plumbing inside the walls can be checked out, but this is the most difficult area of the bathroom to keep an eye on, since the pipes are located inside the walls. Watch for moisture on the drywall or leaking into the floor from any part of the wall. Either of these signs should be a giveaway that there is a problem in the wall.
Texas Residential Water Damage Restoration Contractors
Water Damage Restoration
Protecting Your Deck From Water Damage
Waterproofing your deck that you worked so hard to pay for or to build is something that most homeowners need to do to keep their deck in good condition over the years. It will likely be used extensively and you want to keep it looking as good and as structurally sound as possible. Mold and rotting can occur to decks that are not properly waterproofed, so the deck’s structural integrity is also under scrutiny. Water from a pool or rain or snow can cause the water damage to your deck that you are trying to avoid, so applying a water sealant to the deck will help prevent all of this.
Waterproofing a new deck is not very different from waterproofing one that already exists on a property, but you should wait at least 30 days before you do, because the chemicals in the wood the deck was built with will need time to evaporate and the wood will need time to adjust to its new environment. After you have waited a month, you can start waterproofing the deck.
Clean off the entire deck and remove all furniture. It should be made completely bare and free of all debris, including leaves, sticks, pool toys, and etcetera. You can purchase a cleaner for the deck from most department stores. Follow the directions and apply it with a pump sprayer. When it starts foaming up, get a brush with stiff bristles and start scrubbing the surface of the deck firmly. This will not only remove all the dirt and other buildup from the deck, but also help to remove stains such as grease. After you are done, rinse all of the foam off with your garden hose or a few buckets of water. When you are doing this, you should be wearing eye protection.
Applying the sealant will be done with a roller or a pump sprayer and if there are any puddles of the sealant on the deck, you will have to roll them out so that the sealant coats the deck evenly.
Drilling a few small holes in your deck where water collects can also help further waterproof it. This will let the water drain off of the deck in these areas. They can be as big or as small as you want them to be, although 3/16 of an inch is about the smallest you can get that will allow for a decent amount of drainage.
North Carolina Basement water damage restoration
New Jersey Basement water damage restoration
Waterproofing a new deck is not very different from waterproofing one that already exists on a property, but you should wait at least 30 days before you do, because the chemicals in the wood the deck was built with will need time to evaporate and the wood will need time to adjust to its new environment. After you have waited a month, you can start waterproofing the deck.
Clean off the entire deck and remove all furniture. It should be made completely bare and free of all debris, including leaves, sticks, pool toys, and etcetera. You can purchase a cleaner for the deck from most department stores. Follow the directions and apply it with a pump sprayer. When it starts foaming up, get a brush with stiff bristles and start scrubbing the surface of the deck firmly. This will not only remove all the dirt and other buildup from the deck, but also help to remove stains such as grease. After you are done, rinse all of the foam off with your garden hose or a few buckets of water. When you are doing this, you should be wearing eye protection.
Applying the sealant will be done with a roller or a pump sprayer and if there are any puddles of the sealant on the deck, you will have to roll them out so that the sealant coats the deck evenly.
Drilling a few small holes in your deck where water collects can also help further waterproof it. This will let the water drain off of the deck in these areas. They can be as big or as small as you want them to be, although 3/16 of an inch is about the smallest you can get that will allow for a decent amount of drainage.
North Carolina Basement water damage restoration
New Jersey Basement water damage restoration
Taking Care of Smoke Damaged Clothes
Most clothes that are damaged directly by fire cannot be saved, but those that are damaged only by the soot and ash that is left behind afterward can be if they are taken care of properly. Most often this kind of damage occurs to clothing that is hanging in the closet and becomes engulfed in smoke as the fire ravages another part of the house. Clothes that have soot and ash all over them might not be as difficult as you think that it is, but you still need to take care in the way that you attempt to clean the clothing. Most of this task will be just sorting the clothing into types of fabric and determining when to wash them.
Begin by sorting the clothes by how heavily soiled they are. Lightly soiled items need to be washed first, but they should be shaken out thoroughly first to remove excess soot.
Make piles of clothing and put synthetics with synthetics and organics with organics. Cotton and wool items will be a little more difficult to get the smoke smell out of than synthetic items, but it can be done.
Use as much laundry detergent as the detergent’s manufacturer says to use for every load you need to wash and you should also add one cup of water conditioner. Adding a half a cup of all-fabric bleach will also help. The temperature of the water also matters when washing these soiled clothing items and you should also use the most amount of water that your washer will be able to handle.
Synthetic items should be washed in warm water only in order to stop them from wrinkling when the spin cycle turns on.
All soiled items need to be washed twice and if the soot is still visible, the clothes need to be air dried instead of using the electric dryer. The smoke odor should be gone after they air dry, but if it is not, then the clothes should be aired out outside the house and washed again. Detergents that have perfumes can mask the smell of smoke damage, but after the perfume dissipates, the smell may return.
Chlorinated bleach should not be used on fabric that is organic, because the fabric might have been weakened in certain areas due to the excess heat.
Items that are not subject to dye running, such as very light colors, can be washed in hot water, but this can vary depending on the type of fabric. Look at the clothing tag and see what the care directions say.
Miami Residential Water Damage Restoration Contractors
Orlando water Damage
Begin by sorting the clothes by how heavily soiled they are. Lightly soiled items need to be washed first, but they should be shaken out thoroughly first to remove excess soot.
Make piles of clothing and put synthetics with synthetics and organics with organics. Cotton and wool items will be a little more difficult to get the smoke smell out of than synthetic items, but it can be done.
Use as much laundry detergent as the detergent’s manufacturer says to use for every load you need to wash and you should also add one cup of water conditioner. Adding a half a cup of all-fabric bleach will also help. The temperature of the water also matters when washing these soiled clothing items and you should also use the most amount of water that your washer will be able to handle.
Synthetic items should be washed in warm water only in order to stop them from wrinkling when the spin cycle turns on.
All soiled items need to be washed twice and if the soot is still visible, the clothes need to be air dried instead of using the electric dryer. The smoke odor should be gone after they air dry, but if it is not, then the clothes should be aired out outside the house and washed again. Detergents that have perfumes can mask the smell of smoke damage, but after the perfume dissipates, the smell may return.
Chlorinated bleach should not be used on fabric that is organic, because the fabric might have been weakened in certain areas due to the excess heat.
Items that are not subject to dye running, such as very light colors, can be washed in hot water, but this can vary depending on the type of fabric. Look at the clothing tag and see what the care directions say.
Miami Residential Water Damage Restoration Contractors
Orlando water Damage
Restoration of Water Damaged Papers
One of the first things that should be on your mind after a flood or a hurricane is the important papers and other documents that are in your home inside dressers, desks, and on tables. Sometimes these are the only copies in existence and if you lose them, you might be facing a little bit of inconvenience or you could possibly be facing some legal trouble. Protecting these documents should be one of the first things that you think about when a storm is about to hit and after it is over, you also need to be concerned about how to restore them should they become damaged.
Purchasing a waterproof and fireproof safe is a very good idea if you have any important documents and since most people do, this should apply to you. Whether it is a marriage certificate, birth certificate, warranty on your newly constructed home or large appliance, or any other paper that could have legal significance, you should do your best to make sure that these documents are in a safe place. A waterproof and fireproof safe will help keep these documents protected during times of tragedy striking your house.
Documents should be taken out of standing water before 2 days is up, since mold will start to grow sometime closely afterward. Mold eats organically based items such as paper and wood, so making sure that these items do not become molded is very important. Dry a flat surface to lay these documents onto and open the windows and doors in the home to allow for ventilation. This will help dry the papers out faster.
Any standing water that still exists in your home should be removed, as well. The humidity needs to be lowered as much as you can and the temperature should be put at near 65 degrees Fahrenheit.
Items that need to be taken to a freeze dry facility for restoration should be packed in freezer wrap. Pack these only as tightly as you need to in order to prevent them from sticking to each other in the box. Books should be packed with other like-sized items and papers should be packed in a separate box with other papers. Put your name, address, phone number, and content list on the box and transport it to the facility of your choosing.
New York flood water damage restoration
South Carolina mold remediation
Purchasing a waterproof and fireproof safe is a very good idea if you have any important documents and since most people do, this should apply to you. Whether it is a marriage certificate, birth certificate, warranty on your newly constructed home or large appliance, or any other paper that could have legal significance, you should do your best to make sure that these documents are in a safe place. A waterproof and fireproof safe will help keep these documents protected during times of tragedy striking your house.
Documents should be taken out of standing water before 2 days is up, since mold will start to grow sometime closely afterward. Mold eats organically based items such as paper and wood, so making sure that these items do not become molded is very important. Dry a flat surface to lay these documents onto and open the windows and doors in the home to allow for ventilation. This will help dry the papers out faster.
Any standing water that still exists in your home should be removed, as well. The humidity needs to be lowered as much as you can and the temperature should be put at near 65 degrees Fahrenheit.
Items that need to be taken to a freeze dry facility for restoration should be packed in freezer wrap. Pack these only as tightly as you need to in order to prevent them from sticking to each other in the box. Books should be packed with other like-sized items and papers should be packed in a separate box with other papers. Put your name, address, phone number, and content list on the box and transport it to the facility of your choosing.
New York flood water damage restoration
South Carolina mold remediation
Subscribe to:
Posts (Atom)
